本篇文章給大家談談b367c2是什么材質，以及b363是什么材質對應的知識點，希望對各位有所幫助。

有懂閥門技術英文用語的來幫幫忙

這還不容易么 看我的翻譯 如果可以你就采納我的答案噢~~~！！

Titanium Valves: 1. General shall not, without permission Party casting welding repair process. 2. Material forged titanium material shall be ASTM B381 Gr. F2, or Gr. F3. Casting titanium material shall be ASTM B367 Gr. C2, or Gr. C3. Titanium components, the maximum iron content of 0.07% and the maximum hydrogen capacity of 60ppm. Casting the mechanical properties of casting residue to comply with ASTM requirements. Stick Titanium Standard ASTM B348 Gr.5. 3. X-ray detection casting is subject to 100% X-ray detection test, based on ASTM E446 Class A, B, C 2-class standards, with no D, E, F. 4. Penetrant testing all the casting in the stress test carried out after the required 100% of the permeability test, in order to avoid casting the cracks, trachoma and so on. 5. Certificate B must provide a detailed mechanical performance testing, physical testing, chemical composition of reports and documents. ? Hastelloy alloy valve 1. Castings Hastelloy Castings Hastelloy C4 and the need to use ASTM A494 Grade CW-2M of the alloy, the largest iron content does not exceed 2%. If you specify the use of Hastelloy C276, Ze Xu using UNS N10276 alloy, mechanical properties required to meet the ASTM minimum requirements. 2. X-ray detection for each casting is subject to ultrasonic or X-ray detection. After each batch and then take 10% of the testing, the nominal diameter greater than or equal 6 "of the body in need of complete testing, greater than or equal 8" in key parts of the body just for testing. -Ray flaw detection test based on ASTM E446 Class A, B, C 2-class standards, with no D, E, F. If you have casting did not meet testing standards be admitted to the batch number of the additional testing. If these two happen again does not meet state testing standards, then take all of the batch for testing. 3. Penetrant testing a batch of each supplier is required to provide penetration testing report at the same time need to provide mechanical tests, physical tests and chemical composition of reports. 4. Certificate B must provide a detailed mechanical performance testing, physical testing, chemical composition of reports and documents. ? dual-phase steel valves: 1. A dual-phase steel all of the components required to meet the ASME V111, Div 1, Appendix 7 requirements. 2. Material Duplex steel castings for example, to comply with ASTM A995 Grade 4A for 2205 alloy, grade 6A for the 2507 alloy. Chemical composition, mechanical properties to meet the requirements of subparagraphs 3 to 5. 3. Chemical composition of the amount of corrosion-resistant duplex steel (PREN) according to the formula: PREN = (Cr wt% + 3.3 Mo wt% + 16 N wt%), calculate the value of not less than the following. 2205 Alloy - 34 2507 Alloy - 40 4. Chemical composition requirements are as follows Material 2205 Alloy 2507 Alloy maximum carbon content of 0.030% 0.030% chromium content of 21.5-23% 24-26% nickel content of 4.5-6.5% 5.5-8.0% Mo content of 2.9 -3.5% nitrogen content of 0.145-0.2% 3.6-4.0% 0.24-0.35% maximum sulfur content of 0.02% 0.02% maximum phosphorus content of 0.03% 0.03% maximum silicon content of 1.0% 0.8% maximum manganese content of 2.0% 1.5% tungsten content of 0.5% maximum 0.8% maximum copper content of 0.5% 0.75% 5. mechanical properties requirements are as follows Material 2205 alloy 2507 alloy minimum tensile strength of 620MPa 700MPa 0.2% deformation deflection (minimum) 450 MPa 550MPa Elongation (2in%) 25min 15min maximum stiffness of 290 BHN (30.5 Rc) 310 BFN 6. The remaining test casting heat treatment, the need to use samples of the following tests. Testing methods and the use of the standard details of the Party should be provided. Tension Test ? ? ? Impact Test hardness testing ? corrosion testing 7. Non-destructive testing, after the final heat treatment in accordance with the following annotation can be seen in non-destructive testing penetration testing X-ray detection range of 100% 100% testing a key component of the valve based on ANSI B16 .34 standard ASME VIII Div 1 App 8 ASME VIII Div 1 App 7 processes ASME VIII Div 1 App 8 ASME VIII Div 1 App 7 acceptance ASME VIII Div 1 App 8 ASME VIII Div 1 App 7

可以吧

q235b是什么材質的鋼材

q235b表示屈服點（s）為235MPa的半鎮靜碳素結構鋼。“Q”，代表鋼材的屈服點，后面的數字表示屈服點數值，單位是MPa例如Q235表示屈服點（s）為235MPa的碳素結構鋼。②必要時鋼號后面可標出表示質量等級和脫氧方法的符號。質量等級符號分別為A、B、C、D。脫氧方法符號：F表示沸騰鋼；b表示半鎮靜鋼；Z表示鎮靜鋼；TZ表示特殊鎮靜鋼。

鋼：

鋼是對含碳量質量百分比介于0.02%至2.11%之間的鐵碳合金的統稱。鋼的化學成分可以有很大變化，只含碳元素的鋼稱為碳素鋼（碳鋼）或普通鋼；在實際生產中，鋼往往根據用途的不同含有不同的合金元素，比如：錳、鎳、釩等等。人類對鋼的應用和研究歷史相當悠久，但是直到19世紀貝氏煉鋼法發明之前，鋼的制取都是一項高成本低效率的工作。如今，鋼以其低廉的價格、可靠的性能成為世界上使用最多的材料之一，是建筑業、制造業和人們日常生活中不可或缺的成分。可以說鋼是現代社會的物質基礎。

q235b是什么材質

Q235B是碳鋼的一種代號，表示屈服點為235MPa的B級碳素結構鋼。其化學成分主要是碳、硅、錳、硫、磷、鉻、鎳、銅等。具有一定的伸長率、強度，良好的韌性和鑄造性，易于沖壓和焊接。

ASTMB367Gr.C2是什么材質

ASTM B367-93(2004) 鈦和鈦合金鑄件 Standard Specification for Titanium and Titanium Alloy Castings

你好,看您對閥門的英文翻譯很熟,可以幫我翻譯下嗎?

size unit下IN NS 應該是美標 英寸，BALL VALVE,CL150,RF,TI ASME B367 GR C2 BODY TI TRIM (PPL) SEATS ，球閥，150磅級，RF法蘭，閥體鈦材TI ASME B367 GR C2 這個是標準號，閥座TI TRIM (PPL)也是鈦材的，(FULL)PORT 全通徑，WRENCH CP MSS-SP-72 ASME B16.5，采用手柄操作，手柄的制造、安裝遵循MSS-SP-72 ASME B16.5標準，SP-W TVGRAP GASKET 閥體墊片SP-W TVGRAP 這個好像是一種特殊材料編號，需要問工廠核實，GRAP PACKING 石墨填料。REMARK下這些東西應該是一些技術文件代號。

C2是什么材料

SA-556M C2是ASME SA-556M標準中的管式給水加熱器用碳錳鋼珠光體型鋼，分為直管與規定須彎成“U”型的管子。此鋼號與我國GB5310中的20MnG、25MnG比較接近。

b367c2是什么材質的介紹就聊到這里吧，感謝你花時間閱讀本站內容。